because pseudo quasi crushes are just not good enough
All right. Got a new phone and found that word press has an app. On a side note about the phone, screw Verizon and pretty much everyone else and their high dollar contracts.
Consider me Sir Richard Branson’s Bitch boy because I like what he’s selling. My bill said and done with tax is 38.50 a month with 300 minutes and unlimited data. I was paying 30 alone for just data and had to have a 50 plan for the phone itself. Gross.
Anyway, this seems to work well. So yay!
Sleepy Shmoo
That's right, I got myself a drill press. Picked it up off of Craigslist, it's an old Delta Rockwell.
On this damn outlet box that was sticking up out of the floor. I'll have to see if i have a picture of it somewhere. Here we go, had to crop it but man, this thing is my bane in the dark.
So basically it's just a two gang box on some PVC, it has a 120 and 240 outlet in it. I am always bumping in to it. Needless to say, fixed that mofo right up, or down as it were.
Well, not anywhere close really, but I did upgrade the sub panel in the wood shop. In case anyone electrical stumbles across here, I know it’s not up to code. The original wiring is three instead of four so I am going to have to get a long heavy gauge wire to run as the neutral. But it’s how it was and has worked for decades, so I think I am ok for the moment.
2013.06.07 17:45:12 Just got finished running the neutral so now it’s properly 4 wired. Just have to tie the wire in place now and take up the slack.
Much to the irritation of The Lady Friend, I've put some massively annoying horns on the truck. I might do a write up of it, but I did videos and complied them for YouTube, so here is the tubetube video.
Hhthjithjithjityuihjbh. Tick fbtititibtbitbtibi. It I. Ii. Tigvrviriv. R e I. E. j Ed wj
I'm installing a mini split in the dining room. It is the “hot” side of the house and doesn't get much air flow.
I picked this up off of the Craig's list, up in this nice little retirement village called Sun City.
So I put some new wheels on the truck, and at full lock I got a bit of rubbing on the suspension arms, which es no bueno.
Icky! Shame on me =(
I was trying to think of a way to rig up a steering stop, when a guy from the truck forum i am on told me to just extend the ones there. Hell I didn't even know there were ones there, the little buggers like to hide. Maybe they are obvious to you where they were, but I hadn't spotted them before. I took a look around this morning, lo and behold, here they are!
So I popped them out and took them to the hardware store just to see what size the bolt is. The nut on there is 14mm and the bolt itself has a 10mm head. Undo the nut and the whole thing should just come right out. Don't try to just back the bolt out by itself.
Had I taken a closer look I'd have realized that the hole goes all the way through. Also another thing I realized was after I put the 35mm ones in, even that wasn't enough. I have a 8.5″ wheel with a +25mm offset, so your situation may vary. I'd ended up going with a 50mm in the end. With 35mm I was only about 5 threads into the hole and that didn't leave me with a warm and fuzzy feeling.
Then I had to grind the heads of the bolts down. I had the best results with an angle grinder and a metal sanding disc. I kept a cup of water handy to cool the bolt off as it was getting too hot to touch even through my welding gloves. It took a bit of time but eventually I got them down to where the 10mm socket would fit them. And then I rounded the ends.
Then it's just a matter of putting them in and moving the steering from side to side to see just where you need to adjust them to.
I did this with the car up on a jack so my steering is probably a little less than what it could be since they hit the arms more when they are hanging down. I'll probably work on it more at some point just to give it a bit of fine tuning but all in all this was an easy enough “upgrade” and will save me any further damage on the inside of my wheels.
